Use the mounting bracket that is provided with your SharpV camera to mount the camera in either the top-mounted or bottom-mounted position.
IMPORTANT: Before mounting the camera, make sure that the installation distance and angle respect the SharpV requirements. See Plate read distances for SharpV lenses.
Physical space requirements
Before mounting a SharpV camera unit on a pole or wall, use the following information to confirm that the unit will have the required space to rotate to the required angle for vehicle monitoring.
Side view:
| Letter | Description | Measurement |
|---|---|---|
| Bottom mount | ||
| A | Center of rotation with provided mount | N/A |
| B | Diameter for cable connector | 27.8 cm (10 7/8 in) |
| C | Diameter at edge of camera (without sunshield) | 35.6 cm (14 in) |
| D | Diameter at edge of camera (with sunshield) | 37.9 cm (14 7/8 in) |
| Top mount | ||
| E | Center of rotation with provided mount (without sunshield) | N/A |
| F | Center of rotation with provided mount (with sunshield) | N/A |
| G | Diameter for cable connector (without sunshield) | 27.5 cm (10 13/16 in) |
| H | Diameter for cable connector (with sunshield) | 28.1 cm (11 1/16 in) |
| I | Diameter to edge of camera (without sunshield) | 31.6 cm (12 13/32 in) |
| J | Diameter to edge of camera (with sunshield) | 32.4 cm (12 13/16 in) |
Bottom/top view:
| Letter | Description | Measurement |
|---|---|---|
| Bottom mount | ||
| A | Center of rotation with provided mount | N/A |
| B | Diameter for cable connector | 25.1 cm (9 7/8 in) |
| C | Diameter to edge of camera (without sunshield) | 35.3 cm (13 7/8 in) |
| D | Diameter to edge of camera (with sunshield) | 36.8 cm (14 1/2 in) |
| Top mount | ||
| A | Center of rotation with provided mount | N/A |
| B | Diameter for cable connector | 26.5 cm (10 13/32 in) |
| C | Diameter to edge of camera (without sunshield) | 34.0 cm (13 13/32 in) |
| D | Diameter to edge of camera (with sunshield) | 35.6 cm (14 in) |
Mounting specifications
The supported mounting brackets use the following hole pattern:
| Hardware | Specification |
|---|---|
| Mounting bolts | Type M6 x 1mm |
| Mounting hole distance | 70 mm (2 3/4 in) |
| Mounting hole depth | 9.5 mm (3/8 in) |
- The SharpV body is made of cast aluminum. Using excessive force when tightening the mounting bolts can strip the threads and permanently damage the camera.
- If you are installing a black SharpV, two sets of mounting bolts are provided. The longer (25 mm) bolts must only be used for top-mounted installations that include the sunshield. The sunshield is required for black SharpV cameras that are installed outdoors.WARNING: Only use the longer bolts for top-mounted installations that include the sunshield.
- Always install the provided external serrated lock washers between the bolt head and the
flat washer. WARNING: Failure to install the provided lock washers might cause the mounting bolts to loosen over time. Genetec Inc. is not responsible for any injury resulting from improper mounting.
- The maximum depth of the mounting holes is 9.5 mm (⅜ in). If you are not using the camera mount that is provided, you must calculate the required length of the mounting bolts to ensure that they penetrate the camera body to a depth in the range 6 mm - 9.5 mm (¼ in. - ⅜ in). For information about the length of mounting bolts, see About the SharpV sunshield.WARNING: The camera body can be permanently damaged if you exceed the recommended bolt penetration depth.
- When tightening the mounting bolts, ensure that the torque does not exceed 4N-m (3ft-lb).WARNING: The camera body can be permanently damaged if you exceed the maximum bolt torque.