SharpV mounting hardware - SharpV

A Videotec WBJA (white) or WBJF (black) mounting bracket is included with the SharpV unit. You can also mount the unit using adapters for third-party mounting hardware or using your own custom solution.

If the provided wall mount bracket is not suitable for the installation, you have the following mounting options:

Use one of the provided third-party adapters listed in the Included mounting hardware section.
Purchase one of the Compatible Videotec mounts from a Videotec reseller.
Create a custom solution using the T-slots on the sides of the camera.

Included mounting hardware

When you purchase a SharpV camera unit, mounting hardware is included that is suitable for most wall-mount and pole-mount installations.

Tip: If you lose the rubber plug on the bottom of the camera, you must replace it. Always have extra plugs available (AU-H-SHPVCAPS).

Hardware	Description	Part number
Wall mount bracket	Wall mount bracket with pan-tilt joint Available in black (WBJF) or white (WBJA)	Videotec: WBJF/WBJA AU-H-V-ARM-BLACK AU-H-V-ARM-WHITE
Pole adapter	Adapter for pole mounting of the provided wall mount bracket Supports pole diameters from 7.6 cm (3 in) to 20.3 cm (8 in). Metal straps included. Installation requires a 6 mm (5/16 in) socket.	AU-H-V-POLEADPT-BLACK AU-H-V-POLEADPT-WHITE
Pelco adapter	SharpV Pelco mounting bolt pattern adapter kit	AU-H-V-PELCOADPT-BLACK AU-H-V-PELCOADPT-WHITE
Accessory kit	I/O connection plug RJ45 bayonet plug 2 spare rubber plugs for the reset button port (one black and one white)	AU-H-V-ACCYKIT-G3

Compatible Videotec mounts

The following Videotec mounts are compatible with the SharpV mounting hole pattern. For a full list of compatible Videotec mounting brackets, see the Videotec brackets datasheet.

IMPORTANT: If you purchase a Videotec mounting bracket, ensure that the mounting plate of the bracket you have selected has the same thickness as the provided bracket (WBJA/WBJF). If required, add washers to shim accordingly, so that you do not exceed the maximum bolt depth of 9.5 mm (0.37 in).

NOTE: All Videotec mount are white unless otherwise specified. For color options, contact a Videotec reseller.

Camera mount	Description	Part number
WBJA	Wall mount bracket with pan-tilt joint (white)	AU-H-V-ARM-WHITE
WBJF	Wall mount bracket with pan-tilt joint (black)	AU-H-V-ARM-BLACK
WBMA	Wall mount bracket with pan-tilt joint (short)
WFWCA	Parapet mount with pan-tilt joint
WCM3A	Ceiling bracket with pan-tilt joint (square tubing)
WCM5A	Ceiling mount with pan-tilt joint (round tubing)
WCPA	Reinforcing support plate for poor consistency walls (BHWGC)
WCWA	Corner adapter for WBJA, WBMA
WSFPA	Pole mount adapter for pole diameters 65 mm (2.6 in) to 110 mm (4.3 in). Can mount WBJA or WBMA.
DBHWGC	Pole mount adapter for pole diameters 210 mm (8.3 in) to 225 mm (8.6 in). Requires WCPA to mount WBJA or WBMA.

Videotec customer support

For information about compatible Videotec mounts, contact your Videotec representative:

Americas:: Tel: +1 518-825-0020; Email: info.usa@videotec.com
APAC: Tel: 852 2333 0601; Email: info.hk@videotec.com

EMEA: Tel: 39 0445 697411; Email: info@videotec.com
France and French-speaking countries in Africa: Tel: 33 1 60491816; Email: info.fr@videotec.com

For a full list of contacts, see http://www.videotec.com/en/page_556.html.

SharpV mounting hardware - SharpV | SharpOS 14.3

AutoVu™ SharpV Installation Guide 14.3

Included mounting hardware

Compatible Videotec mounts

Videotec customer support