Configuring the SharpZ3 system to use a specific IP address range in the SharpOS 13.7 Sharp Portal - SharpZ3 | SharpOS 13.7

AutoVu™ SharpZ3 Administrator Guide 13.7
Product
SharpZ3
Content type
Guides > Administrator guides
Version
13.7
Language
English
Last updated
2024-09-06

By default, the SharpZ3 base unit and modules communicate using their default static IP addresses and no configuration is necessary. If required, you can define new static IP addresses within a specific range.

Before you begin

Learn about SharpZ3 network settings.

What you should know

The IP address range that is assigned to the SharpZ3 system must account for the SharpZ3 base unit and all connected modules.

In an example using a 192.168.0.X range, the following addresses are required when all SharpZ3 expansion slots are in use:

Module Default static IP addres
ALPR module ports 1 and 2 192.168.0.1
ALPR module ports 3 and 4 192.168.0.2
EXP 1: Navigation expansion module 192.168.0.30
EXP 2: AUX PoE expansion module 1 192.168.0.40

192.168.0.41 (Port 1)

192.168.0.42 (Port 2)

192.168.0.43 (Port 3)

192.168.0.44 (Port 4)
EXP 3: AUX PoE expansion module 2 192.168.0.50

192.168.0.51 (Port 1)

192.168.0.52 (Port 2)

192.168.0.53 (Port 3)

192.168.0.54 (Port 4)

Procedure

  1. Log on to the Sharp Portal.
  2. From the Configuration menu, select the Network page.
  3. Select Use static IP address.
    The network settings are displayed for the ALPR module for each installed expansion module.
  4. In the IPv4 network settings section, configure the ALPR module network settings, .
    You can modify the following:
    IP address
    Enter the new IP address you want to assign to the ALPR module. The default is 192.168.10.1 (port 1 and 2) and 192.168.10.2 (port 3 and 4).
    Subnet mask
    Enter the new Subnet mask for the ALPR module, if applicable. The default is 255.255.255.0.
    IMPORTANT: When assigning specific IP addresses, ensure the configuration stays compatible with the rest of the system, otherwise the base unit, expansion modules, or aux cameras might be unreachable. For example, it is important that all components be on the same subnet.
    Gateway
    Enter the new Gateway for the ALPR module, if applicable. The default is 10.0.0.0.
    DNS
    Enter the new DNS for the ALPR module, if applicable. The default is 10.0.0.0.
  5. If the system includes a navigation expansion module, enter its new IP address and update the Subnet mask if required.
  6. If the system includes AUX PoE expansion modules, enter their new IP address and update the Subnet mask if required.
    The AUX PoE expansion modules automatically assigns compatible IP addresses to each PoE port on the same subnet. For example if you configure an AUX PoE expansion module to use the static IP address 192.168.0.40, then the first PoE port will be 192.168.0.41, second will be 192.168.0.42, and so on.
  7. Click Save.
  8. If the ALPR module includes four camera ports, log on to Sharp Portal 2 and enter the new static IP address for the second pair of camera ports.
    A two-camera ALPR module is configured through one Sharp Portal; a four-camera ALPR module is configured through two Sharp Portals.
    Sharp Portal 1 (camera ports 1 and 2)
    http://192.168.10.1/
    Sharp Portal 2 (camera ports 3 and 4)
    http://192.168.10.2/
    SharpZ3 base unit with hardware ports for Sharp Portal 1 and Sharp Portal 2
  9. Click Save.
Parent topic: About SharpZ3 network settings