Creating a RabbitMQ Cluster - Genetec Mission Control™

Genetec Mission Control™ Deployment Guide

Applies to
Genetec Mission Control™
Last updated
Content type
Guides > Deployment guides
Genetec Mission Control™

A RabbitMQ cluster is a feature that enables the synchronization of state data and configurations of multiple nodes, in a real-time networked environment. It adds failover protection and, in some cases, performance gains.


To create a RabbitMQ cluster:

  1. Copy the .erlang.cookie files from the master node:
    By default in a Windows system, there is an .erlang.cookie file in two different locations in the master node. They are found in:

      This usually leads to C:\Windows\ServiceProfiles\LocalService\ for a service


      This usually leads to C:\Users\<username>

  2. Copy the cookies from each location and overwrite the cookie files in the same file path of the destination nodes.
  3. Copy the following certificate files from the master node and overwrite them to the other nodes:
    • CACert.pem
    • Cert.pem
    • Fingerprint.txt
    • Key.pem

    By default, these files are found in C:\Program Files (x86)\Genetec\RabbitMQ\.

    NOTE: If the Incident Manager role is on a separate machine, then you must copy the certificates from the RabbitMQ server to the server hosting the Incident Manager role.

Modify the RabbitMQ configuration files on the master node to enable partition handling:

  1. Right-click the Notepad application, select Run as administrator, and then open the RabbitMQ.conf file in Notepad.
    By default, the RabbitMQ configuration file, RabbitMQ.conf, is found in C:\ProgramData\Genetec\RabbitMQ\config.
    Tip: Using Notepad++ with Makefile set as language improves the readability of the file.
  2. Modify the following line from:
    # cluster_partition_handling = pause_minority
    cluster_partition_handling = pause_minority
    By removing the # symbol, the line is no longer flagged as a comment and becomes part of the code.
  3. Save the file.

Reinstall the RabbitMQ service to enable the configuration file changes:

  1. Right-click the RabbitMQ Command Prompt (sbin dir) application and select Run as administrator.
    This is installed with RabbitMQ by default.
  2. Execute the following commands:
    1. rabbitmq-service.bat remove
      When successfully executed, the following message is displayed:
      Service RabbitMQ removed from system
    2. rabbitmq-service.bat install
      When successfully executed, the following message is displayed:
      Service RabbitMQ added to system
    3. rabbitmq-service.bat start
      When successfully executed, the following message is displayed:
      The RabbitMQ service is starting. The RabbitMQ service was started successfully.

Ensure that your modified configuration file is loaded in memory:

  1. In the RabbitMQ Command Prompt application, execute the following command: rabbitmqctl.bat environment
    When successfully executed, the content of the RabbitMQ.conf file is loaded in memory and the following message is displayed in a format similar to a JSON file:
    Application environment of node rabbit@<User>
  2. Verify that your modifications have been implemented correctly:
    1. Ensure that the modified configuration reads as follows:
      cluster_partition_handling = pause_minority
    2. If the line of code does not read as in the previous step, modify it to match.

Copy the modified RabbitMQ.conf file to the other nodes:

  1. Copy the modified RabbitMQ.conf file from the master node.
    The default location of the config file is C:\ProgramData\Genetec\RabbitMQ\config\.
  2. Overwrite the existing RabbitMQ.conf file in the same file path of the destination nodes.
    It is recommended to do a backup before you overwrite the existing files.
  3. Reinstall RabbitMQ service for each node.