Creating parking permits - Security Center 5.7

Security Center Administrator Guide 5.7

Applies to
Security Center 5.7
Last updated
2021-12-16
Content type
Guides > Administrator guides
Language
English (United States)
Product
Security Center
Version
5.7

To use permit entities in Security Center, you must create the permit, map it to its source text file, and configure it for your enforcement scenario.

What you should know

If you are using University Parking Enforcement, you must also apply restrictions to permits to create an enforcement rule.

Procedure

  1. From the Config Tool home page, click LPR > Permits, then click Permit ().

    The Creating a permit wizard opens.

  2. On the Basic information page, in the Entity name field, type a name for the permit.
    This name appears in Genetec Patroller™ on the permit selection page.
    IMPORTANT: The permit entity name must match the Category field from the permit list source file.
  3. (Optional) In the Entity description field, enter a description for the new permit, and click Next.
    This field does not appear in Genetec Patroller™.
  4. Enter the Path on the computer where the source file for the permit list is located.

    If you start typing a path to a network drive, the Username and Password fields appear and you’ll need to type the username and password to access the network drive.

  5. If the attribute fields in the source text file vary in length, switch the Use delimiters option to ON, and enter the type of character (delimiter) used to separate each field.

    By default, Use delimiters is set to ON, and the delimiter specified is a semi-colon (;). If your source text file is made up of fixed length fields, set Use delimiters to Off . Security Center supports the following delimiters:

    • Colon (:)
    • Comma (,)
    • Semi-colon (;)
    • Tab (type “Tab”)
    IMPORTANT: If your source list file uses Tab as a delimiter, only use one Tab space. Do not use more than one Tab space to align columns in your file, or Security Center might not be able to parse the permit list.
    NOTE: The maximum number of entries is 1.8 million when using Genetec Patroller™ in 64-bit mode. Adding more entries causes the system to respond slowly.
  6. (Optional) If you don't want users to be allowed to edit this permit in Security Desk, turn off Visible in editor.
    NOTE: To edit a permit in Security Desk, users must have the Hotlist and permit editor privilege.
  7. Configure the permit Attributes and click Next. See Configuring hotlist and permit attributes.
  8. On the LPR Manager assignment page, choose one of the following, then click Next.
    • All LPR Managers. All LPR Managers and any entities configured to inherit permits from them will synchronize the new permit.
      NOTE: Future LPR Managers will not automatically synchronize the new permit.
    • Specific LPR Managers. Only the selected LPR Managers and the entities that inherit permits from them will synchronize the new permit.
      NOTE: Entities created in the future that are configured to inherit permits from one of the selected LPR Managers will also synchronize the permit.
  9. In the Unit specific assignment page, select the specific patrol vehicles and/or Sharp cameras that will synchronize the new permit, and click Next.
  10. (Optional) If you have custom fields in your permit, enter the appropriate values on the Custom fields page and click Next.
    NOTE: The Custom fields page only appears if there are custom fields in your hotlist.
  11. In the Creation summary window, check to see that your permit information is correct and click Next.
  12. In the Entity creation outcome window, you will receive a notification whether or not your operation is successful.
  13. (Optional) Choose one of the following:
    • Edit this permit. Opens the Hotlist and permit editor task so you can edit the permit.
      NOTE: To edit a permit, you must have the Hotlist and permit editor privilege.
    • Create a permit based on this permit: Create a new permit that uses the same settings as the permit you just created. You only need to specify the Entity name, Entity description, and Permit path.
  14. Click Close.

Results

The permit entity is configured and enabled in Security Center.