Supported configurations for the SVA-100E and SV-100E series
These Streamvault™ appliance series support various deployment scenarios for video-only systems, and for unified video and access control systems, both with or without remote viewing from the Genetec™ Mobile application on your smartphone.
The configuration of your Streamvault™ appliance deployment determines the maximum number of cameras you can install, and the maximum video quality that can be configured for those cameras. Above this maximum video quality, problems might occur with recording video and viewing live and recorded video streams."
Video only deployment using Mobile Server for remote monitoring
When using a Streamvault™ appliance to record video and monitor video remotely using the Genetec™ Mobile application, the following maximum configuration is supported:- Sixteen cameras recording at 2 Mbps per camera, for a maximum of 32 Mbps of traffic on the network
- Sixteen video streams redirected at 2 Mbps per stream
- Five video streams transcoded to five mobile devices, using a remote stream configured to a default value of 8 fps 640 x 480
The following requirements must be met:
- Software motion detection must be deactivated.
- Each camera must support at least two streams.
Video only deployment using Mobile Server for local monitoring
When a Streamvault™ appliance is used to record video and monitor video locally using the Genetec™ Mobile application, the following maximum configuration is supported:- Sixteen cameras recording at 2 Mbps per camera, for a maximum of 32 Mbps of traffic on the network
- Five video streams transcoded to five mobile devices, using a remote stream configured to a default value of 8 fps 640 x 480
The following requirements must be met:
- IP cameras or encoders must connect to a network switch on the same IP network as the appliance.
- Software motion detection must be deactivated.
The following configuration is recommended:
- Dynamic stream selection is enabled for cameras that support multi-streaming.
The number of video streams that the appliance can display locally depends on the video stream quality (resolution, frame rate, bit rate) configured for H.264 cameras. The following table shows several scenarios:
| Resolution | 5 fps | 15 fps | 30 fps |
|---|---|---|---|
| 640 x 480 | 16 cameras at 600 Kbps | 16 cameras at 1200 Kbps | 8 cameras at 2000 Kbps |
| 1280 x 720 | 16 cameras at 700 Kbps | 9 cameras at 1500 Kbps | 4 cameras at 2500 Kbps |
| 1920 x 1080 | 15 cameras at 1200 Kbps | 5 cameras at 3000 Kbps | 3 cameras at 3000 Kbps |
Unified deployment using Mobile Server for remote monitoring
When using a Streamvault™ appliance for access control and to record and monitor camera video remotely from a Genetec™ Mobile, the following maximum number of devices and video streams are supported:- Sixteen cameras recording at 2 Mbps per camera, for a maximum of 32 Mbps of traffic on the network
- Sixteen readers
- Sixteen video streams redirected at 2 Mbps per stream
- Five video streams transcoded to five mobile devices
The following requirement must be met:
- Software motion detection must be deactivated.
Unified deployment using Mobile Server for local monitoring
When using a Streamvault™ appliance for access control and to record and monitor camera video locally from a Genetec™ Mobile, the following maximum number of devices and video streams are supported:- Sixteen cameras recording at 2 Mbps per camera, for a maximum of 32 Mbps of traffic on the network
- Sixteen readers
- Five video streams transcoded to five mobile devices
The following requirements must be met:
- IP cameras or encoders must connect to a network switch on the same IP network as the appliance.
- Software motion detection must be deactivated.
| Resolution | 5 fps | 15 fps | 30 fps |
|---|---|---|---|
| 640 x 480 | 16 cameras at 600 Kbps | 11 cameras at 1200 Kbps | 5 cameras at 2000 Kbps |
| 1280 x 720 | 16 cameras at 700 Kbps | 5 cameras at 1500 Kbps | 2 cameras at 2500 Kbps |
| 1920 x 1080 | 7 cameras at 1200 Kbps | 1 cameras at 3000 Kbps | 1 cameras at 3000 Kbps |
Supported configurations in SV-300E and SV-300E-T4 series
The SV-300E and SV-300E-T4 series support various video configurations when the client application is local or remote from the Streamvault™ appliance.
Server-only mode: remote video monitoring
- Up to 100 cameras
- Recording H.264 at 2 Mbps per camera
- Live monitoring from an external workstation using multicast
Client server mode: local video monitoring
When a client application is installed locally, the SV-300E and SV-300E-T4 series support the following configurations for H.264 streaming:
| Resolution | 5 fps | 15 fps | 30 fps |
|---|---|---|---|
| 640 x 480 | 32 cameras at 600 Kbps | 26 cameras at 1200 Kbps | 13 cameras at 2000 Kbps |
| 1280 x 720 | 32 cameras at 700 Kbps | 17 cameras at 1500 Kbps | 8 cameras at 2500 Kbps |
| 1920 x 1080 | 24 cameras at 1200 Kbps | 8 cameras at 3000 Kbps | 5 cameras at 3000 Kbps |
Supported access control configurations in SV-300E and SV-300E-T4 series
The SV-300E and SV-300E-T4 series support up to 100 access control readers when used with supported controllers.
- Genetec™Synergis™ Cloud Link controllers
- HID EDGE and EDGE EVO controllers
- HID VertX and VertX EVO controllers
- Mercury controllers
- Axis controllers
- Assa Abloy IP lock controllers