Cameras not recording - Security Center 5.9 - 5.13

If you can’t record video, or if there are missing video archives or gaps in the archives, you can determine the cause of the issue.

1. Verify that Security Center supports the unit, and that the unit is running the certified firmware.
   For a list of video units supported by Security Center, see our Supported Device List.
2. Verify the camera recording type to ensure that the camera is set to record video on the correct schedule:
   1. In the Config Tool Video task, select your camera.
   2. Click the Recording tab.
      • If the Recording settings option is set to Custom settings, ensure that all the recording settings are correct, and then click Apply.
      • If the Recording settings option is set to Inherit from Archiver, continue with the next substep.
   3. In Video task, select the Archiver.
   4. Click the Camera default settings tab.
   5. In the Recording modes section, make sure that the Archiver is set to record on the correct Schedule, and that the recording Mode isn’t set to OFF.
   6. If the Custom settings per server option is enabled, make sure that archiving is enabled on the server the Archiver should be recording on.
3. If the camera recording mode is set to On motion / Manual, ensure that motion detection settings are configured properly:
   1. In the Config Tool Video task, select your camera.
   2. Click Video analytics > Motion detection.
   3. Verify the motion detection settings.
4. Check the status of the Archiver role database:
   1. In the Config Tool Video task, select the Archiver.
   2. Click the Resources tab.
      • If the Archiver database status is Connected, go to the next troubleshooting step.
      • If the Archiver database status is Disconnected or Unavailable, continue with the next substep.
   3. Switch to a different archive database or create a new one.
      CAUTION:

      Perform this step at a noncritical time, because all the units connected to the Archiver will temporarily go offline. Don’t delete or overwrite the existing database, or your video archives will be deleted.

      1. In the Database field, enter a different name and click Apply.
      2. Wait for the role to connect to the new database. If the database doesn’t exist, it will be created.
      3. If the camera can record using the new database, you can continue to use the new database.
         CAUTION:
         When you switch to a different database, the video archives referenced in the old database are no longer included in Security Center searches, and won’t be deleted by the Archiver's automatic cleanup.
      4. If the camera is still not recording, revert back to the original database, and continue with the next troubleshooting step.
5. Check how much disk space is available for archiving:
   1. In the Config Tool Video task, select the Archiver.
   2. Click the Resources tab.
   3. In the disk information table, make sure the Min. free space value is at least 0.2% of the total disk space.
      The Min. free space is the minimum amount of free space that the Archiver must leave untouched on the disk.
   4. If the Min. free space value is less than 0.2% of the total disk space, click the value and increase it.
      To see the total disk space, point the mouse cursor to the Disk usage meter.
      
6. Check for Archiving stopped and Recording stopped events that occurred on your system.
   In Windows, on the server where the Archiver role is running, open the .log files, found in C:\ArchiverLogs.

   If there are Archiving stopped or Recording stopped events in the Entry type column, restart the Genetec™ Server service:

   1. Open your Windows Control Panel.
   2. Click Administrative Tools > Services.
   3. Right-click the Genetec™ Server service and click Restart.
7. Check for Transmission lost and RTP packets lost events that occurred on your system.
   In Windows on the server where the Archiver role is running, open the .log files, found in C:\ArchiverLogs.
   • If there are many Transmissions lost and RTP packets lost events in the Entry type column, there could be a CPU usage or network issue. Continue with the next troubleshooting step.
   • If there aren’t many Transmission lost and RTP packets lost events, then skip the next troubleshooting step.
8. Check your CPU usage:
   1. Right-click the Windows taskbar and open Windows Task Manager.
   2. Click the Performance tab, and check that the CPU Usage is below 60%.
      If the CPU usage is over 60%, restart the server, and consider adding more CPU to the server.
   3. Click the Networking tab, and make sure the network Link speed isn’t over 300 Mbps.
9. If you’re only experiencing recording problems with one video unit, try the following:
   1. In the Config Tool Video task, right-click the red video unit and click Delete.
   2. In the confirmation dialog box, choose whether you want to keep the video archives from the unit.
      The video unit is removed from the Archiver.
   3. Add the video unit. For information, see Adding video units manually.