Adding your Quanergy M1 Edge lidar as a tracking system to Security Center - To monitor the restricted areas secured by your Quanergy M1 Edge lidar system in Security Center, you must first add each M1 Edge device to a driver container in the Inter-System Gateway (IS Gateway). Then, you need to add the driver container as a tracking system to Config Tool. - Restricted Security Area Surveillance

To monitor the restricted areas secured by your QuanergyM1 Edge lidar system in Security Center, you must first add each M1 Edge device to a driver container in the Inter-System Gateway (IS Gateway). Then, you need to add the driver container as a tracking system to Config Tool.

1. Log on to the IS Gateway web portal:
   1. Open a web browser and enter the URL https://<GatewayServer>:4242.
      <GatewayServer> is the name or IP address of the server hosting the IS Gateway service. The default port is 4242. Use the port you configured at installation.
   2. Accept the security certificate.
   3. On the logon page, enter the Username and Password and click Sign in.
      The username and password were assigned during the Inter-System Gateway Configuration step of the IS Gateway service installation.
2. Add a driver container for the tracking system that you want to add to Security Center:
   1. On the homepage of the IS Gateway, click the Container () tab.
   2. Click the button besides the docker engine label, and then click Add driver container.
   3. In the Add driver container window that opens, enter the following information:
      

      Driver

      Select the driver that you want to install.

      Version

      Select the driver version that you want. The latest version is selected by default.

      Label

      Label used to identify this driver container in the list of containers on the left.

      Port

      Port used to communicate with the driver.

      Network adapter

      Select the network adapter used by the driver to communicate with the IS Gateway service.

      Show advanced

      Some drivers require other communication ports to be open. If necessary, click here to add those ports.

   4. Click Add.
      The IS Gateway immediately downloads the required driver container image from the repository. A notification is shown in the upper right corner of the browser page during the download process.

      

      After the download completes, the new driver container is displayed in the list of containers on the left, under the selected docker engine.

      
   5. Start the driver container. To do so, click the button beside the driver container label and click Start.
   NOTE: If you are adding multiple driver containers, make sure that each driver container has a unique port number. This will prevent any port conflicts if multiple driver containers are running at the same time.
3. Select the driver container corresponding to the tracking system that you want to add to Security Center.
4. In the Communication section, click Add ().
   
5. In the Add/Edit device window that opens, enter the following information:
   

   Name

   Enter a unique name for this device.

   Model

   Select M1 Edge Sensor.

   IP Address

   The IP address of the device.

   Latitude and Longitude

   Enter the coordinates of the device. Coordinates are in decimal degrees using the World Geodetic System (WGS84) format. You can use a web site like https://www.latlong.net/ to find the coordinates of a specific civic address.

   Elevation

   Height of the device from the ground, in meters.

   Bearing

   If the device has a field of view, identify the physical orientation of the device using compass points. For example: If the device's field of view points towards true North, set the orientation to 0 degrees. You can use a compass to find the degrees.

6. Click OK.
   The Quanergy M1 Edge device is listed under Devices in the Communication section.
7. In the Events section under M1 Edge Sensor Events, turn on the custom events that you want to monitor for this tracking system.
   
8. Click Save.
9. Add your driver container as a tracking system to Security Center:
   1. From the Config Tool homepage, open the Plugins task.
   2. From the entity tree, select the Restricted Security Area Surveillance plugin role.
   3. Click Add an entity (), and select Tracking system.
      The Add tracking system dialog box opens.
   4. From the Type drop-down, select Inter-System Gateway.
   5. In the Name field, enter a name for your tracking system.
   6. From the Model drop-down, select the driver container you are adding and click Next ().
   7. If applicable, configure the specific settings for your driver and click Next ().
   8. If applicable, import the map from the third-party application and click Finish.
   9. Open the Area view task.
      After a few seconds, your tracking system () should be added to the area view.